Bathtub installation Rexburg ID done right the first time

When you need bathtub installation Rexburg ID homeowners can count on, we handle the whole job: old tub out, new tub set level, drain and overflow tied in, supply lines pressure-tested.

Serving rexburg and nearby areas.

How big is the tub job?

Drain work

Tub swap plus trap arm correction or drain line repair behind the wall.

  1. 1. Swap only Standard alcove tub out, new tub in, existing drain and valve reused.
  2. 2. Drain work Tub swap plus trap arm correction or drain line repair behind the wall.
  3. 3. Full rebuild Subfloor repair, new drain and valve, and a planned walk-in or conversion.
  • 24Services from one local team
  • 15Areas served around rexburg
  • Camera firstWe look inside the drain before setting the tub
  • Pressure testSupply lines held at 80 psi before we close up

What our bathtub installation includes

Every tub install covers removal, disposal, setting, drain and supply connections, and a full leak test.

Bathtub Installation in rexburg, Idaho

Work order

Bathtub Installation
  • Old tub removal and disposal: We cut the caulk line, disconnect the drain and overflow, and lift the old tub out without damaging the surround. The tub leaves with us, so you are not paying a dump fee or storing a cast iron tub in the garage.
  • Drain and overflow connection: We install a new drain shoe, overflow gasket, and plumber's putty seal, then confirm the trap arm slope meets code. This is the step that prevents the slow drip that rots subfloor over a year.
  • Supply line and valve work: We connect the supply lines, install or reuse the valve trim, and pressure-test at 80 psi. If the shutoffs are seized or the PEX crimping tool shows a bad fitting, we correct it during the same visit.
  • Leveling and mortar bed: The tub goes onto a mortar bed and is leveled side to side and front to back. A tub that rocks will crack the caulk line within months. We check level twice before the drain goes in.
  • Fill-and-drain leak test: We fill the tub to the overflow, let it sit, then drain it while watching for drips at the shoe and overflow. If access below exists, we check the ceiling. You see the test before we leave.
  • Caulk, cleanup, and walkthrough: A clean silicone bead goes around the rim, we wipe the bathroom down, and we show you how the new valve works. You get a reminder to leave the caulk undisturbed for 24 hours.

What the first visit covers

First visit

We measure the alcove, check the drain and subfloor, and note the valve condition so the install plan is set.

Bathtub installation at your home

We handle tub swaps, walk-in installs, and drain repairs in Rexburg homes.

  • Leaking tub drain

    Overflow gasket and drain shoe replaced during the install.

  • Cracked acrylic pan

    New tub set on a mortar bed for full support.

  • Walk-in tub upgrade

    Low-threshold tub with a reinforced subfloor.

  • Tub to shower conversion

    Drain re-routed and valve replaced for a shower pan.

plumber rexburg id — plumber rexburg id you can rely on

Bathtub installation for Rexburg properties

We work with landlords, property managers, and student housing near campus.

  • Rental turnover

    Tub swaps scheduled between leases to keep units rent-ready.

  • Student housing

    Heavy-use tubs replaced with durable acrylic models.

  • Multi-unit properties

    Repeat installs with consistent parts and drain work.

Bathtub installation Rexburg ID: what the job actually involves

A tub that leaks or flexes will cost more to fix later than to install correctly now. We set it level, connect the drain, and test it before we leave.

It is not a drop-in job. We check joist condition, measure the alcove to the quarter inch, and confirm the drain shoe lines up before the tub ever leaves the truck.

In Rexburg, most tub calls start the same way: a cracked acrylic pan, a rusted steel tub from the 1970s, or a slow drain that has been patched twice already. If you are searching for bathtub replacement near me Rexburg, we can usually walk the bathroom, quote the swap, and schedule the install inside the same week. Winter makes it urgent. A failed tub drain in January can send water into a ceiling below before you notice the stain.

Dependable plumber rexburg id across rexburg, Idaho
What it is
Removing an old tub and installing a new one with drain and valve work.
When it helps
Leaks, cracks, slow drains, or a tub that is hard to step into.
What you get
A level tub, a tested drain, and a clean caulk line.

How our bathtub installation process works

Every job follows the same five steps. You know what is happening, when the water gets shut off, and when the bathroom is usable again.

  1. Walkthrough and measure

    We inspect the alcove, measure width, depth, and drain offset, and check the subfloor for soft spots or old water damage.

  2. Water off and demo

    We shut off the supply, cut the old caulk line, and lift the existing tub out without damaging the surround or floor tile.

  3. Rough-in corrections

    If the drain is out of alignment or the old valve is a two-handle relic, we correct it now.

  4. Set and connect the tub

    The new tub goes onto a mortar bed for full support, leveled side to side and front to back.

  5. Test, caulk, and clean

    We fill the tub to the overflow, let it sit, then drain it while watching the ceiling below if access allows.

Tools and methods we use on tub installs

Each method answers a different question. Together they leave very little to guess.

Used to break loose old drain fittings and clear the trap arm before the new tub goes in. A seized drain shoe will not come out by hand.

Clears hair, soap scum, and scale from the branch line. Hydro jetting is used when the line is heavily scaled and a snake alone will not restore full flow.

Lets us see inside the drain line before and after the install. We use it to confirm the trap arm is clear and the pipe is not cracked or bellied.

For supply line work. PEX crimping handles modern tubing runs, and the soldering torch is used on copper pipe repairs where the existing line is copper.

We pressure-test the supply at 80 psi after connecting the valve and supply lines. If the gauge drops, there is a leak we need to find before closing up.

When Rexburg homeowners call for a tub install

  • A rental near the BYU-Idaho Campus Area needs a tub swapped between tenants during a one-week turnover.

    We schedule the install on turnover day, pull the old acrylic pan, correct the drain slope, and set a new American Standard…

    Homes
  • A 1970s home near Downtown Rexburg has a rusted steel tub leaking into the basement ceiling.

    We cut out the old tub, inspect the subfloor and trap arm, replace the corroded drain section with ABS pipe, and set…

    Homes
  • A family in Mill Hollow needs a walk-in tub for an aging parent who can no longer step over a standard rim.

    We reinforce the subfloor, set the walk-in tub on a mortar bed, connect the drain and overflow, and install a Moen valve…

    Homes
  • A homeowner near Rexburg Town Square wants to replace a tub with a low-threshold shower during a bathroom update.

    We handle the tub to shower conversion Rexburg project: pull the tub, cap or re-route the drain, install a shower pan and…

    Homes

How bathtub installation works in Rexburg

Rexburg sits at about 4,900 feet, and winter nights regularly drop below zero. That matters for tub installs because supply lines in exterior walls are at risk of freezing, and we often add insulation or re-route PEX tubing while the wall is open.

  • Downtown Rexburg

    Older homes with cast iron drains and original steel tubs. We often find corroded trap arms that need replacing during the install.

  • Mill Hollow

    Newer construction with ABS pipe and PEX supply. Tub swaps here are usually straightforward, but we still check the drain slope.

  • BYU-Idaho Campus Area

    High rental turnover means tubs take heavy use. We schedule installs on turnover days to keep units rent-ready.

plumbing service for rexburg homes
  • Downtown Rexburg
  • Mill Hollow
  • BYU-Idaho Campus Area
  • The Cottages
  • Hemming Village

From problem to finished result.

Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.

Dependable plumber rexburg id across rexburg, IdahoPhoto
  • Rusted steel tub to Kohler acrylic

    Before: A 1978 steel tub near Downtown Rexburg had rusted through near the drain and was leaking into the basement ceiling. The overflow gasket was brittle, the trap arm was corroded, and the shutoff valves were seized open.

    After: We removed the old tub, replaced the corroded trap arm with ABS pipe, installed new shutoff valves, and set a Kohler acrylic tub on a mortar bed. The fill-and-drain test held with no drips, and the basement ceiling stain stopped growing.

  • Walk-in tub for aging parent

    Before: A family in Mill Hollow needed a walk-in tub for an aging parent who could no longer step over a standard 15-inch rim. The existing subfloor had a soft spot near the drain from a slow leak.

    After: We reinforced the subfloor, set a walk-in tub on a mortar bed, and installed a Moen valve with a handheld sprayer. The door seal passed a full fill-and-drain test, and the parent can bathe without assistance.

  • Tub to shower conversion near town square

    Before: A homeowner near Rexburg Town Square wanted more floor space and an easier-to-clean fixture. The old tub was sound but the drain was slow, and the two-handle valve was hard to turn.

    After: We pulled the tub, re-routed the drain for a shower pan, installed a new single-handle valve, and coordinated the permit and inspection. The conversion passed inspection, and the bathroom gained about 8 square feet of usable floor.

Tub problems we solve for Rexburg homeowners

Most tub calls fall into one of four buckets: leaks, cracks, drain clogs, or accessibility.

Ask about yours

  • Tub leaking into the ceiling below

    Water travels along joists and can rot subfloor, stain drywall, and grow mold within weeks.

  • Cracked or flexing acrylic tub floor

    A flexing tub floor will eventually crack through, and the water goes straight into the subfloor.

  • Slow drain that returns after snaking

    A tub that pools water is usually a partially blocked trap arm or a sagging drain line, not just hair.

  • Tub too high to step into safely

    A standard tub rim sits 14 to 16 inches off the floor, which is a fall risk for older adults or anyone recovering from surgery.

Why Rexburg homeowners upgrade the tub

A new tub is not cosmetic. It stops leaks, restores resale value, and gives you a bathing surface that actually holds water without flexing underfoot.

Stops hidden leaks

A failed overflow gasket or cracked pan can drip 5 to 10 gallons a day into the floor structure.

Restores resale value

A clean, code-correct tub install is one of the few bathroom upgrades that appraisers can verify.

Fits walk-in needs

Walk in bathtub installation in Rexburg, Idaho is the right call when a family member needs a low 3- to 4-inch threshold.

Ends the slow-drain cycle

A tub that pools water is usually a partially blocked trap arm or a sagging drain line, not just hair.

What bathtub installation costs in Rexburg

The price goes up when we find rotten subfloor, a cracked drain line, or a valve that needs replacing.

Included

Quoted after a first look

  • Old tub removal and disposal
  • Drain and overflow connection
  • Supply line and valve work
  • Leveling and mortar bed
Request Service

What you receive on a tub job

Clear records you can keep and share.

  • Written scope

    Tub model, valve brand, and any drain repairs listed.

  • Drain photos

    Camera images of the trap arm before and after.

  • Test record

    Notes from the fill-and-drain and pressure tests.

Before work starts

A plan in writing

Ask for a written scope

Bathtub installation expertise you can verify

We work to the International Plumbing Code and Uniform Plumbing Code on every drain and supply connection.

plumbing service in rexburg, Idaho

Trap arm slope

We check the fall on the drain line to confirm it meets code and drains fully.

Subfloor condition

We probe for soft spots and rot before setting the new tub on a mortar bed.

Valve condition

We check the cartridge and shutoffs to decide whether to rebuild or replace.

Is your Rexburg area covered?

Type your ZIP code or town. If you are nearby and not listed, ask us.

rexburg ZIP codes

  • 83460
  • 83440

What Rexburg customers say

Our old steel tub had rusted through near the drain and was leaking into the basement ceiling. They came out, quoted the replacement the same day, and had a new Kohler tub set and tested by the next afternoon. They replaced the overflow gasket and wax ring without me asking. The ceiling stain has not grown since.
Megan R.Homeowner, Mill Hollow
I manage four rentals near campus and needed a tub swapped between tenants fast. They scheduled it on a turnover day, pulled the old acrylic pan, corrected the drain slope, and had the new tub in before the next lease started. No callbacks from the tenants, which is rare for me.
Dave T.Landlord, BYU-Idaho Campus Area
We needed a walk-in tub for my father and were worried about the door seal. The crew reinforced the subfloor, set the tub on a mortar bed, and walked us through the fill-and-drain test. It has been six months with no leaks and no creaking. They also replaced the shutoff valves while they were in there.
Carol H.Homeowner, Rexburg Town Square

Frequently asked questions about bathtub installation

Short answers for the first few minutes. The team can cover the rest.

Still have a question?

Describe what you are seeing and we will point you to the right next step.

+12089875089

The variables are tub type, whether the drain needs re-routing, and whether the subfloor has water damage. We quote it in writing before we start.

A standard alcove tub swap takes one day, usually six to eight hours from water-off to cleanup. Walk-in tub installation in Rexburg, Idaho can run a full day plus a short return visit if the door seal needs a second look. If we find rotten subfloor or a cracked drain line, add a day for the repair. We tell you the realistic timeline before we schedule.

Yes. Our bathtub installation service near me calls include the drain, overflow, supply lines, and valve trim, not just setting the tub. We replace the wax ring and overflow gasket, pressure-test the supply at 80 psi, and correct any trap arm slope that fails code. If the shutoff valves are seized or the PEX crimping tool reveals a bad fitting, we fix that during the same visit.

Yes. We install walk-in tubs with low 3- to 4-inch thresholds, and we reinforce the subfloor and set the tub on a mortar bed so the door seal stays true. Most walk-in installs take one day. We also handle tub to shower conversion Rexburg projects when a low-threshold shower makes more sense for the household. Both options get the same drain and valve inspection.

Schedule your bathtub installation Rexburg ID today

+12089875089

We quote the job in writing, show up when we say we will, and test the drain before we leave.

Contact Plumber Rexburg ID

Call us at +1 (208) 987-5089 or email info@plumberrexburgid.com. For non-emergency service, we schedule same-day or next-day appointments. Our office is in Rexburg, and we serve all of Madison County.

Request a visit

How soon do you need us?

Thanks. Your request is in and the team will follow up shortly.

Call now+12089875089